Accessories

  • Thick Steel washer for spacing hub motor axles 3mm
    Quick View
    Thick Steel washer for spacing hub motor axles 3 mm Typically used to extend hub motor axle length Laser cut from steel Outer diameter small enough to fit inside freewheel opening without rubbing Fits over 10mm motor axles
    A$3.00
  • Stainless Steel Spacer for Disk Calliper Clearance

    Out of stock

    Quick View
    Stainless Steel Spacer for Disk Calliper Clearance 1.00 mm. Stops the break calliper rubbing on the hub motor and increases clearance.
    A$6.00

    Out of stock

  • Temperature sensor wire
    Quick View
    2 pin temperature sensor red wire form hub motor to controller Cable length:100 cm, Male and female connectors.
    A$12.00
  • FUSE HOLDER WITH ANDERSON PLUG 40 AMP
    Quick View
    FUSE HOLDER WITH ANDERSON PLUG 40 AMP WITH BLADE FUSE
    A$15.00
  • FUSE HOLDER WITH INSULATED TERMINALS 50 AMP
    Quick View
    FUSE HOLDER WITH INSULATED TERMINALS 50 AMP
    A$15.00
  • Full Twist Grip Throttle
    Quick View
    Full Twist Grip Throttle
    A$25.00
  • Split Twist Grip Throttle
    Quick View
    Split Twist Grip Throttle
    A$25.00
  • 16 Tooth Single Speed Freewheel
    Quick View
    16 Tooth Single Speed Freewheel
    A$25.00
  • Thumb Throttle
    Quick View
    Thumb Throttle
    A$25.00
  • Push Button (regen braking)
    Quick View
    Push Button (regen braking)
    A$25.00
  • Wire Loop With Key

    Out of stock

    Quick View
    Wire Loop With Key
    A$25.00

    Out of stock

  • 7 Speed Gear Freewheel

    Out of stock

    Quick View
    7 Speed Gear Freewheel
    A$30.00

    Out of stock

  • 8 Speed Gear Freewheel
    Quick View
    8 Speed Gear Freewheel
    A$30.00
  • Full Twist Grip Throttle with battery indicator 36V
    Quick View
    Full Twist Grip Throttle with battery indicator 36V
    A$50.00
  • Full Twist Grip Throttle with battery indicator 48V
    Quick View
    Full Twist Grip Throttle with battery indicator 48V
    A$50.00
  • 3 Speed Switch

    Out of stock

    Quick View
    3 speed adjustment: It is used to adjust the motor output current with 25% (L), 50% (M), 100% (H) output. In order to set motor speed on the road L = Low speed, M = Middle speed, H = High speed.
    A$50.00

    Out of stock

  • On & Off Switch
    Quick View
    On & Off Switch
    A$50.00
  • 24" double rim, black  (Sample Picture Only)
    Quick View
    24" double rim, black (Sample Picture Only)
    A$75.10
  • FRONT FORK LEFT AND RIGHT TORQUE ARM SET (FITS CRYSTALYTE HUB MOTORS).
    Quick View
    All of our stainless steel torque arms are currently laser cut in Australia and assembled and finished. We use thick 6mm stainless steel plate with anti-rotation slot and nylon lock nuts stainless steel fasteners as well. Torque arms are used to prevent axle rotation in hub motors. When a hub motor is powered up running, for all the torque that the motor generates spinning a wheel forwards, there is an equal and opposite torque on the axle causing it to rotate backwards "Newton's Third Law ". In most electric bicycle hub motors, the axle is machined with flats on either side which key into the dropout slot and provide some measure of support against rotation. In many cases this is sufficient. However, in high power systems 500 watts and upwards it will generate a lot of torque, or in setups with weak dropouts, the forces present can exceed the material strength and pry the dropout open. When that happens, the axle will spin freely, wrapping and severing off the motor cables and potentially causing the wheel to fall right out of the bike. Front Fork Torque Arm: 6 mm Thick Suit 10mm Hub Motor Axle. Stainless Steel.
    A$85.00
  • REAR DROP-OUT LEFT AND RIGHT TORQUE ARM SET. (FITS CRYSTALYTE HUB MOTORS).
    Quick View
    All of our stainless steel torque arms are currently laser cut in Australia and assembled and finished. We use thick 6mm stainless steel plate with anti-rotation slot and nylon lock nuts stainless steel fasteners as well. Torque arms are used to prevent axle rotation in hub motors. When a hub motor is powered up running, for all the torque that the motor generates spinning a wheel forwards, there is an equal and opposite torque on the axle causing it to rotate backwards "Newton's Third Law ". In most electric bicycle hub motors, the axle is machined with flats on either side which key into the dropout slot and provide some measure of support against rotation. In many cases this is sufficient. However, in high power systems 500 watts and upwards it will generate a lot of torque, or in setups with weak dropouts, the forces present can exceed the material strength and pry the dropout open. When that happens, the axle will spin freely, wrapping and severing off the motor cables and potentially causing the wheel to fall right out of the bike. Rear Torque Arm: 6 mm Thick Suit 10mm Hub Motor Axle. Stainless Steel.
    A$85.00
   WARRANTY 12 month
 FAST SHIPPING 
 Need help? 0427 770 768